Plumber's Essentials: Your Key to Installing a Bathtub
Plumber's Essentials: Your Key to Installing a Bathtub
Blog Article
We have discovered this post involving A Step-by-Step Guide to Installing a Bathtub below on the internet and decided it made good sense to talk about it with you on this page.
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
Installing a bath tub isn't specifically brain surgery, but it does need solid plumbing, woodworking, and also occasionally, tiling abilities. Replacing an old bath tub with a new one is also a reasonably hard project. If the old bathtub is readily easily accessible, the job can move rapidly; if you have to open up a wall surface to remove the old tub and also position the brand-new bath tub, the task is much harder. In either instance, the job is within a residence handyman's abilities, although you will certainly need an assistant to vacate the old tub and set in the brand-new one. Make sure you have actually qualified yourself for the work and also fit attempting it. Instead of employing a contractor to take control of a halfway-completed task, it is far better to consider utilizing one prior to you begin. Chances are you might require an expert plumber to make tube links.
This short article will assist you mount a new bath tub in your restroom if you have actually already bought a brand-new bathtub and don't require to alter the plan of your previous supply of water pipelines.
Your devices and also material checklist should make up the following:
Preparing for the Installment
Firstly, the supporting frame supplied with the bath needs to be fitted (if called for) according to the supplier's instructions. Next, fit the taps or mixer to the tub. When suitable the tap block, it is important to make sure that if the faucet comes with a plastic washer, it is fitted between the bathroom and the taps. On a plastic bath, it is additionally sensible to fit a supporting plate under the faucets system to stop stress on the bathtub.
Fit the flexible tap adapters to the bottom of both taps using 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet through the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make sure you use every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath must currently be ready to be fitted in its last setting.
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your installation, then the first thing you need to do is detach the supply of water. After doing so, activate the faucets to drain pipes any type of water staying in the system. The procedure of eliminating the existing taps can be quite bothersome because of the restricted gain access to that is typically the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipes to the taps. Have a towel prepared for the remaining water that will originate from the pipes. When the supply pipes have actually been removed, use the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from transforming during this process. As soon as the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any old securing substance.
Before going on to fit the brand-new taps, contrast the pipeline connections on the old taps to the new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Installing the Tub
Using the two wooden boards under its feet, position the bathtub in the required position. The wood boards are handy in uniformly spreading the weight of the bathtub over the area of the boards rather than focusing all the weight onto 4 little factors.
The following objective is to make certain that the bathtub is leveled all round. This can be accomplished by inspecting the spirit level and also readjusting the feet on the tub up until the level checks out level.
To install faucets, fit all-time low of the furthest versatile faucet port to the ideal supply pipeline by making a compression sign up with; after that do the exact same for the other tap.
Switch on the water and also inspect all joints and also new pipework for leakages and tighten them if essential. Fill up the tub and additionally check the overflow outlet as well as the typical electrical outlet for leaks.
Ultimately, fix the bathroom paneling as explained in the producer's instruction manual. Tiling as well as securing around the tub should wait till the tub has actually been used a minimum of when as this will certainly settle it into its final setting.
Suitable New Taps
If the tails of the new taps are plastic, then you will certainly need a plastic port to avoid damage to the string. One end of the adapter fits on the plastic tail of the tap and the other end provides a link to the existent supply pipelines.
If you need to fit a monobloc, then you will call for lowering couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the faucet in the placing hole in the bath/basin making certain that the washers are in area in between the tap and the sink. Protect the faucet in place with the maker given backnut. When the tap is safely in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with regular tap connectors. The former kind should be connected to the tap ends initially, tightening only by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the location where the bathroom fulfills the tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the installation can relocate sufficient to break a rigid seal, creating the water to pass through the wall between the bath and the tiling, resulting in problems with wetness as well as possible leakages to the ceiling listed below.
You can select from a selection of coloured sealers to assimilate your components as well as installations. They are marketed in tubes as well as cartridges, and are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of drenched paper or soft rope. Remember to always fill the tub with water before sealing, to enable the motion experienced when the bathtub is in use. The sealant can fracture rather early if you do not take into consideration this motion before sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise conveniently offered on the marketplace. It is suggested to fit the floor tiles utilizing water-resistant or water resistant adhesive and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an enthusiastic person who reads about How to Install a Bathtub, I figured sharing that editorial was worthwhile. Enjoyed reading our blog? Please share it. Let somebody else discover it. Bless you for your time. Visit again soon.
Book Inspection Report this page